MKT-D-04696 Rev A
DEMO ONLY. This interactive simulation is provided solely for training and demonstration purposes. It does not control or communicate with an Enterra Ascent® IPG and is not intended for patient care, clinical decision-making, or use as a substitute for the approved labeling, instructions for use, or required training.
Current flows between the positive (+) and negative (-) electrodes.
The electrode configuration must include at least one positive (+) and one negative (-) electrode.
Take a therapy impedance measurement (above) to calculate the voltage value.
The calculated voltage will reach maximum at 10.5 V.
Loading Therapy settings…
Programming successful
The following information provides the essential information needed to navigate the Enterra Entrust® Clinician Programmer.
What does “Shelf Mode” mean?
If the IPG is new out of the box, it will be in a low-power state, also referred to as “Shelf Mode”. After the Clinician Programmer connects to the IPG for the first time, the IPG will no longer be in Shelf Mode.
How do I navigate the different functions in the app?
The navigation panel provides access to the app menus and programming functions. Tap the desired icon to navigate to the screen for that function. By default, the navigation panel is in a collapsed state and shows the icons only. To expand the navigation panel and show the icon descriptions, tap 
at the top of the panel. Tap it again to collapse the panel.
How do I turn stimulation to the IPG On and Off?
To turn stimulation to the IPG On or Off, refer to the title bar at the top of the screen. The title bar displays the name of the active screen and provides access to the IPG stimulation On/Off toggle button. When turning stimulation On or Off, a confirmation pop-up dialog box will display. Tap Turn On Stimulation or Turn Off Stimulation as appropriate.
How do I exit the app when I am finished with a programming session?
On the navigation panel, tap the End Session icon 
and then tap End Session on the confirmation pop-up dialog box.
How do I contact Enterra Medical for assistance?
On the navigation panel, tap the About icon, and the company contact information, application firmware, and software version are displayed.
How do I edit the various fields in the Patient Demographics screen?
What should I do if I see a warning stating that the device has entered Safe Mode?
How do I measure the system’s impedance?
icon and then tap Measure Impedance. All measurements will then be displayed. If all impedances are within range, a green checkmark appears next to each value confirming that the values are within a safe range. If a value is out of range, a caution symbol will be displayed. A lighting bolt icon 
identifies the currently active electrodes.How do I check the battery status of the IPG?
on the navigation panel. The remaining battery capacity percentage is displayed.How do I measure the system’s impedance?
Navigate to the Programming screen by tapping the 
icon and then tap Measure Impedance. The measurement for the active electrodes will then be displayed. If the impedance is within range, a green checkmark appears next to the value confirming it is within a safe range. If the value is out of range, a caution symbol will be displayed.
What IPG settings are on the Programming Screen?
To edit a field, tap the field and select the appropriate setting from the dropdown menu.
Below is a list of editable fields:
Please note that the Electrode Configuration is located at the bottom of the screen.
How do I save or reset the IPG parameter settings?
To save and implement IPG setting changes, tap Program IPG.
To reset the IPG settings to the most recent programmed settings before you save any changes, tap Clear Changes. To reset the IPG settings to the IPG’s default settings, tap Reset to Nominal.
How do I view past programming sessions?
Tap the Programming History icon 
on the navigation panel. This screen displays the 80 most recent programming sessions; the most recent session is displayed at the top of the screen.
Please note that this screen is view-only and cannot be edited.
How do I generate and review a programming session report?
On the navigation panel, tap the Reports icon 
to navigate to the Reports screen. To generate one or more reports, tap the desired Generate report or Export button. When the report is generated, you have three options: close the dialog box, view the report, and open the Downloads folder, which is where the report is stored.
Can I save a copy of a report to a separate device?
Yes, you can transfer a copy of a report to a compatible USB drive from the Downloads folder.
What if I forget the Report’s password?
In the event that you forget the password, you can generate a new password by tapping the Set New Password button at the bottom of the Reports screen. Reports under the previous password will no longer be accessible. To access those reports, please contact Enterra Medical for assistance.
For additional information or more details on a particular function, please refer to the Enterra Entrust User Guide, which can be found on Enterra Medical’s website.
800-03099-001 Rev C, 2025-10
Enterra Medical
5353 Wayzata Boulevard, Suite 400
St. Louis Park, MN 55416
Phone: (855) 768-3772
Version: 1.0.0
UDI: 123123123123123
Android: 12
Stimulation is off. Are you sure you want to end the session?